Reset Procedures
Tools Needed:
- None required - manual reset procedures only
Step-by-Step Reset Methods
- Basic Power Reset: Turn off the dishwasher at the circuit breaker or unplug it from the power source. Wait 2 minutes, then restore power.
- Control Lock Reset: Press and hold the "Heated Dry" and "Cycle Select" buttons simultaneously for 3 seconds to unlock controls.
- Factory Reset: Press and hold "Heated Dry" + "Normal" + "Heavy" buttons for 5 seconds until all lights flash. Release to reset to factory defaults.
- Drain Reset: If dishwasher won't drain, press "Cancel/Drain" button for 3 seconds to initiate manual drain cycle.
- Water Heating Reset: Press "Heated Dry" and "High Temp Wash" simultaneously for 3 seconds to reset heating system.
- Sensor Reset: Run diagnostic mode by pressing "Heated Dry" + "Normal" for 5 seconds to reset all sensors.
- Complete System Reset: Disconnect power for 10 minutes, then restart with a test cycle.
Error Codes
| Model Series | WDF520PADM7 |
| Type | Built-in Dishwasher |
| Color | Stainless Steel / Black |
| Place Settings | 14 Place Settings |
| Noise Level | 50 dB |
| Control Type | Electronic Touch Controls |
| Energy Rating | ENERGY STAR® Certified |
| Water Consumption | 3.2 Gallons per Cycle |
| Power Requirements | 120V, 60Hz, 15A |
| Dimensions (HxWxD) | 34.5 x 23.8 x 24.5 inches |
| Weight | 85 lbs |
| Wash Cycles | 5 Wash Cycles + Options |
Warranty Information
- Full Warranty: 1 year parts and labor
- Motor Warranty: 10 years on wash motor
- Racks Warranty: Lifetime on stainless steel tub and rack
- Additional Coverage: Optional extended warranty available
For warranty service, contact Whirlpool Customer Service at 1-800-253-1301 or visit Whirlpool.com
Specifications
Sensor Cycle Technology
Advanced sensors automatically adjust water temperature, cycle time, and wash actions based on soil level for optimal cleaning performance.
Soil Sensor
Detects food soil levels and adjusts cycle accordingly, ensuring thorough cleaning while conserving water and energy.
Hard Food Disposer
Built-in hard food disposer eliminates the need for pre-rinsing by grinding up food particles during the wash cycle.
Stemware Cycle
Specialty cycle designed to gently clean delicate stemware and fine china with reduced water pressure and temperature.
Sanitize Cycle
NSF certified sanitize cycle eliminates 99.9% of household bacteria with final rinse water heated to 155°F.
Top Control Design
Hidden controls on top of door provide sleek appearance while remaining easily accessible during operation.
Wash Cycle Options
Normal Wash
Standard cycle for everyday dishes with normal soil levels
Heavy Wash
Intensive cleaning for pots, pans, and heavily soiled items
Light Wash
Quick cycle for lightly soiled dishes and glassware
Rinse Only
Rinses dishes without detergent to prevent drying
Stemware Cycle
Gentle cleaning for delicate glassware and fine china
Sanitize Cycle
High-temperature cycle that eliminates bacteria
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Dishwasher won't start | Door not latched, power issue, control lock enabled | Ensure door closed properly, check power supply, disable control lock |
| Poor cleaning results | Clogged spray arms, wrong detergent, overloaded | Clean spray arms, use recommended detergent, reduce load size |
| Water not draining | Drain hose clogged, air gap blocked, filter dirty | Check drain hose, clean air gap, clean filter assembly |
| Leaking water | Door seal damaged, overfilling, loose connections | Check door gasket, ensure proper detergent amount, check connections |
| Unusual noises | Foreign objects in pump, spray arm hitting dishes | Check for foreign objects, rearrange dishes properly |
| Error codes displayed | Sensor failure, motor issue, water flow problems | Perform reset procedure, check water supply, contact service |
Error Codes
- F1: Water temperature issue - Check heating element and thermostat
- F2: Water fill issue - Check water supply and inlet valve
- F3: Drain issue - Check drain pump and hose
- F4: Water level sensor issue - Contact service center
- F5: Motor control issue - Perform system reset
- F6: Control panel communication error - Reset control board
- F7: Heater relay issue - Contact authorized service
- F8: Overflow detected - Check float switch and water level
Manual Downloads
Current Model Manuals
WDF520PADM7
Built-in Dishwasher
WDF540PADM7
Stainless Steel Interior
WDF560PADM7
Third Rack Model
WDF580PADM7
Wi-Fi Enabled Model
Popular Previous Models
WDF750SAYM0
Stainless Steel
WDF760SAYM0
Black Stainless
WDF780SAYM0
Fingerprint Resistant
WDF790SAYM0
Stainless Steel